will be 4 KiB (containing file itself and some junk).
@item -nice
Set desired outgoing packet @ref{Niceness, niceness level}.
- 1-255 values are allowed.
@item -replynice
Set desired reply packet @ref{Niceness, niceness level}. Only freq
- and exec packets look at that niceness level. 1-255 values are
- allowed.
-@item -node
- Process only single specified node.
+ and exec packets look at that niceness level.
@item -via
Override @ref{CfgVia, via} configuration option for destination node.
Specified nodes must be separated with comma: @verb{|NODE1,NODE2|}.
+ With @verb{|-via -|} you can disable relaying at all.
@item -spool
Override path to spool directory. May be specified by
@env{NNCPSPOOL} environment variable.
% dd if=/dev/cd0 bs=2048 | nncp-bundle -rx -delete
@end verbatim
-@option{-dryrun} option prevents any writing to the spool. This is
+@option{-dryrun} option prevents any writes to the spool. This is
useful when you need to see what packets will pass by and possibly check
their integrity.
@section nncp-call
@verbatim
-% nncp-call [options] [-onlinedeadline INT] [-maxonlinetime INT] [-rx|-tx]
- NODE[:ADDR] [FORCEADDR]
+% nncp-call [options]
+ [-onlinedeadline INT]
+ [-maxonlinetime INT]
+ [-rx|-tx]
+ [-rxrate INT]
+ [-txrate INT]
+ NODE[:ADDR] [FORCEADDR]
@end verbatim
Call (connect to) specified @option{NODE} and run @ref{Sync,
only outbound transmission is performed. @option{-onlinedeadline}
overrides @ref{CfgOnlineDeadline, @emph{onlinedeadline}}.
@option{-maxonlinetime} overrides @ref{CfgMaxOnlineTime,
-@emph{maxonlinetime}}.
+@emph{maxonlinetime}}. @option{-rxrate}/@option{-txrate} override
+@ref{CfgXxRate, rxrate/txrate}.
@node nncp-caller
@section nncp-caller
@section nncp-daemon
@verbatim
-% nncp-daemon [options] [-maxconn INT] [-bind ADDR]
+% nncp-daemon [options] [-maxconn INT] [-bind ADDR] [-inetd]
@end verbatim
Start listening TCP daemon, wait for incoming connections and run
can handle. @option{-bind} option specifies @option{addr:port} it must
bind to and listen.
+It could be run as @command{inetd} service, by specifying
+@option{-inetd} option. Example inetd-entry:
+
+@verbatim
+uucp stream tcp6 nowait nncpuser /usr/local/bin/nncp-daemon nncp-daemon -inetd
+@end verbatim
+
@node nncp-exec
@section nncp-exec
If @file{SRC} equals to @file{-}, then create an encrypted temporary
file and copy everything taken from stdin to it and use for outbound
packet creation. Pay attention that if you want to send 1 GiB of data
-taken from stdin, then you have to have 2 GiB of disk space for that
-temporary file and resulting encrypted packet. You can control where
-temporary file will be stored using @env{TMPDIR} environment variable.
-Encryption is performed with @url{https://cr.yp.to/chacha.html,
-ChaCha20} algorithm. Data is splitted on 128 KiB blocks. Each block is
-encrypted with increasing nonce counter.
+taken from stdin, then you have to have more than 2 GiB of disk space
+for that temporary file and resulting encrypted packet. You can control
+where temporary file will be stored using @env{TMPDIR} environment
+variable. Encryption is performed in AEAD mode with
+@url{https://cr.yp.to/chacha.html, ChaCha20}-@url{https://en.wikipedia.org/wiki/Poly1305, Poly1305}
+algorithms. Data is splitted on 128 KiB blocks. Each block is encrypted
+with increasing nonce counter.
If @option{-chunked} is specified, then source file will be split
@ref{Chunked, on chunks}. @option{INT} is the desired chunk size in
@verbatim
% nncp-pkt [options] < pkt
% nncp-pkt [options] [-decompress] -dump < pkt > payload
+% nncp-pkt -overheads
@end verbatim
Low level packet parser. Normally it should not be used, but can help in
tries to zlib-decompress the data from plain packet (useful for mail
packets).
+@option{-overheads} options print encrypted, plain and size header overheads.
+
@node nncp-reass
@section nncp-reass
@section nncp-stat
@verbatim
-% nncp-stat [options]
+% nncp-stat [options] [-node NODE]
@end verbatim
Print current @ref{Spool, spool} statistics about unsent and unprocessed
-packets. For each node and each niceness level there will be printed how
-many packets (with the total size) are in inbound (Rx) and outbound (Tx)
-queues.
+packets. For each node (unless @option{-node} specified) and each
+niceness level there will be printed how many packets (with the total
+size) are in inbound (Rx) and outbound (Tx) queues.
@node nncp-toss
@section nncp-toss
@verbatim
% nncp-toss [options]
+ [-node NODE]
[-dryrun]
[-cycle INT]
[-seen]
[-nofile]
[-nofreq]
- [-nomail]
+ [-noexec]
[-notrns]
@end verbatim
running this command as a daemon.
@option{-seen} option creates empty @file{XXX.seen} file after
-successful tossing of @file{XXX} packet. @ref{nncp-xfer} and
-@ref{nncp-bundle} commands skip inbound packets that has been already
-seen, processed and tossed. This is helpful to defeat duplicates.
+successful tossing of @file{XXX} packet. @ref{nncp-xfer},
+@ref{nncp-bundle}, @ref{nncp-daemon} and @ref{nncp-call} commands skip
+inbound packets that has been already seen, processed and tossed. This
+is helpful to prevent duplicates.
-@option{-nofile}, @option{-nofreq}, @option{-nomail}, @option{-notrns}
+@option{-nofile}, @option{-nofreq}, @option{-noexec}, @option{-notrns}
options allow to disable any kind of packet types processing.
@node nncp-xfer
@section nncp-xfer
@verbatim
-% nncp-xfer [options] [-mkdir] [-keep] [-rx|-tx] DIR
+% nncp-xfer [options] [-node NODE] [-mkdir] [-keep] [-rx|-tx] DIR
@end verbatim
Search for directory in @file{DIR} containing inbound packets for us and